Best Nightlatch Locks for Wooden Front Doors: Security & Installation Guide

Best Nightlatch Locks for Wooden Front Doors: Security & Installation Guide

A nightlatch is a type of lock that is commonly used on Australian timber front doors. This surface-mounted lock is designed to be installed on the interior face of a door, with a key cylinder located on the exterior and a snib or handle positioned within the lock. The product is straightforward to install and replace, however, the selection of type is crucial, particularly for those who prioritise insurance, break-in resistance or fire compliance.


Rim Nightlatches vs Deadlocking Nightlatches

These are not actually opposites. It should be noted that the vast majority of nightlatches are of the "rim lock" variety. This means that they are designed to be positioned on the surface of the door, as opposed to being set into a pocket that has been cut into the door's edge. The key distinction is whether the latch is deadlocking.

  • A standard rim nightlatch has a spring-loaded latch that snaps shut when the door closes. It can usually be retracted by sliding a thin tool or card between the door and the frame.
  • A deadlocking nightlatch has a small plunger or auxiliary bolt that locks the latch in place once the door closes. This stops the latch being pushed back, which makes the door significantly harder to open without the key.

For a front door, a deadlocking nightlatch is the better choice. Browse Keeler's nightlatches range and look for the deadlocking or "deadlatch" function in the product description.

 

Nightlatch, Deadbolt or Mortice Lock?

A nightlatch is convenient but is generally a lighter-duty product than the alternatives.

  • Deadbolts add a thick bolt that throws into the frame and are designed to resist forcing. Many people fit one above a nightlatch for a second locking point.
  • Residential mortice locks sit inside the door and combine latch and bolt. They suit solid timber doors that are thick enough to be cut for the lock body.

If you are not sure which suits your door, the mortice section of our guide to identifying and replacing a mortice lock explains how to read the existing preparation.

 

Backset: Getting the Measurement Right

For a nightlatch, backset is the distance from the edge of the door to the centre of the cylinder hole. The two sizes you will see most often are 40mm and 60mm. A narrower stile, such as on a timber door with glass panels, may only suit the shorter backset, while a solid timber door usually accommodates the longer one.

To measure:

  1. Open the door and locate the cylinder hole on the outer face
  2. Measure from the edge of the door to the centre of that hole
  3. Compare the result to the backset listed for each lock

If you are matching an existing nightlatch, also check the cylinder hole diameter and the position of the fixing holes on the inside, since these vary between brands. Keeler's lock accessories range includes packers, strikers and screws that help adapt a new lock to old preparation.

 

Fitting a Nightlatch to a Timber Door

Timber doors are forgiving, but a few details make the difference between a secure fit and a weak one.

  1. Use the template. Mark the cylinder hole position carefully. Drill from the outside with a hole saw, and finish from the inside to avoid splintering the face.
  2. Check the door's condition. Soft, split or rotten timber will not hold screws. Repair the area first.
  3. Fit the lock body with the supplied screws. Do not substitute shorter ones.
  4. Align the strike. The strike plate on the frame must line up with the latch. Use long screws that reach the framing behind the jamb, because short screws into thin timber are the usual point of failure in a forced entry.
  5. Test with the door open. Operate the key and snib several times before closing the door.

Many break-ins exploit a weak frame, not a weak lock. A blocker plate or latch guard covers the gap between the door and frame, so it is harder to slip a tool in. It is a cheap upgrade for any timber door with a visible gap.

 

Insurance and Security Points

Insurers generally require a key-operated deadlock or deadbolt on external doors, though the specific requirements can vary between policies and providers. It is imperative to verify your product disclosure statement or contact your insurer before relying solely on a nightlatch. If there is glass within reach of the inside snib or thumb-turn, a keyed inside operation reduces the risk of someone breaking the glass and reaching in. It is important to consider the need to be able to exit quickly in an emergency.

 

Fire-Rated Doors: Where Nightlatches Fit

If you are searching for a fire-rated nightlatch, it is first necessary to determine whether your door is actually a fire door. In many Australian multi-residential buildings, apartment entry doors are fire-rated, and some doors in townhouses and commercial buildings are also fire-rated. A fire door is tested as a complete doorset under standards such as AS 1905.1, which includes the door, frame, seals and hardware.

That has two implications:

  • Do not replace hardware on a fire door based on size alone. The replacement lock must be approved for that specific doorset.
  • Surface-mounted nightlatches are generally not part of a tested fire doorset. Fire doors more often use mortice locks designed and tested for the purpose.

If your door has a fire tag on the hinge edge, please check the certification or speak to the building manager or a qualified certifier before changing the lock. However, for non-fire-rated doors, such as those found in typical house entries, this restriction does not apply.

 

Final Check Before Ordering

  • Confirm the door is timber and not a fire-rated doorset
  • Measure the backset, 40mm or 60mm
  • Decide on the deadlocking function
  • Check the cylinder hole size and the fixing hole positions
  • Plan a deadbolt or reinforcement if the door is the main entry
  • Confirm any insurer requirements

For help choosing, call us on 1300 533 500 or visit our North Willoughby or Wetherill Park store.

Back to blog