Please note that some doors are not compatible with handles that protrude. A pocket door is installed into a wall cavity, a sliding cabinet door is positioned adjacent to its neighbour, and a flush cabinet front is designed to create the impression of a single, uninterrupted surface. In each case the handle needs to sit inside the door rather than on top of it. That is what joinery handles and recessed pulls are for.

What is a Flush Mount or Recessed Pull?
A flush pull is installed within a cut-out in the face of the door, with its outer surface level with, or slightly below, the surrounding panel. A recessed pull typically has a deeper finger space behind a smaller opening. Both options provide a secure grip without any protrusions, making them suitable for a range of applications.
Common types include:
- Round and rectangular flush pulls that are fixed into a routed recess
- Edge pulls that attach to the edge of the door
- Finger pulls and cups that are fitted into a hole or cut-out
For doors that slide into a cavity, Keeler's range of flush door handles and cavity sliding door hardware is worth reviewing alongside joinery handles.

Recess Depth and Door Thickness
It is vital to note that recess depth is the most crucial specification. It is used to determine if a pull is compatible with the dimensions of your door..
Typical door and panel thicknesses vary:
- Internal pocket doors are commonly around 35mm thick
- Cabinet doors and drawer fronts are usually 16mm to 20mm thick
A pull with a deep recess may be suitable for a thick pocket door, but it should be avoided for a thin cabinet panel, as cutting too deeply could weaken the face or break through the back. It is imperative to always check the product's recess depth, cut-out size and the template or drawing supplied by the manufacturer. In situations where there is a limited amount of material available, it is advisable to opt for a shallow pull or an edge pull.
Installing a Flush Pull in a Pocket Door
Pocket doors are less forgiving than hinged doors because the handle must be reachable when the door is closed and must not catch on anything when it slides into the wall.
- Choose a pull with enough finger space to pull the door out of the cavity from the edge, with the door fully retracted.
- Check clearance. The pull must not project beyond the door face, otherwise it can snag on the cavity or frame.
- Mark the position at a comfortable height, normally in line with where you would place a standard handle.
- Cut the recess using a template. A router with a guide gives the cleanest result. Cut to the specified depth and test-fit before fixing.
- Fix and test. Slide the door fully in and out several times and check for contact.
If your pocket door also needs a lock, a cavity door lock may be required, and some flush pulls are designed to work with them.
Flush Pulls for Cabinet Fronts and Drawers
In the case of a cabinet front that is flush with the surrounding surface, a recessed pull is selected to ensure that the handle does not disrupt the linear aesthetic of the joinery. It is especially useful in confined spaces, such as near walkways, where a protruding handle could snag clothing.
Check the finger clearance behind the pull. People with larger hands or limited grip strength may find very shallow recesses hard to use. For drawers and standard cabinet doors, Keeler's drawer handle and pulls and cupboard knobs and handles offer protruding alternatives where a flush look is not essential. Our article on cabinet hardware that is built to last covers durability points that apply to both styles.
Commercial vs Residential Joinery Hardware
Office storage systems, reception counters and shared cabinets see far more use than home joinery, and the hardware needs to handle it.
|
Residential |
Commercial |
|
|
Use |
A few times a day |
Dozens of times a day |
|
Materials |
Zinc, aluminium, brass |
Stainless steel, heavy-gauge aluminium |
|
Fixings |
Standard screws |
Heavier or concealed fixings |
|
Locking |
Sometimes |
Often needed for security or privacy |
|
Accessibility |
Optional |
Often a design requirement |
For workplaces, accessibility is an important factor to consider. Recessed pulls can pose challenges for individuals with limited grip or dexterity, and Australian guidance such as AS 1428.1 on access and mobility influences the design of handles and fittings in many commercial settings. If an accessible option is required, ensure that the pull can be used with one hand and does not require a tight grasp.
Final Check Before Ordering
- Measure the door or panel thickness
- Check the recess depth and cut-out size against the product specification
- Confirm that the pull sits flush and will not snag
- Choose a material and finish suited to the use, residential or commercial
- Allow for locking or accessibility needs
- Use a template and test-fit before final fixing
Need help matching a handle to a door? Call us on 1300 533 500 or visit our showroom.